PARTES

[ O-RING 19X1MM 16MM (4) ]

[ 3X56MM BH SCREW (8 PCS)  ]

[ LIGHTWEIGHT BRAKE DISK ADAPTER ]

[ SHOCK BODY 16MM IGT8 19 ]

[ 3X43MM BH SCREW (8) ]

[ FRONT MIDDLE SHAFT LIGHTWEIGHT ]

[ PINS 2X14MM (16 PCS) 1/8 TH ]

[ SILICONE O-RING 3.4x2  (10) ]

[ ALU LIGHTWEIGHT LOCATING COLLAR (2) ]

[ SHOCK SPRING ADJUSTER 16MM ]

[ INNER HINGE PINS 3X55MM (2) ]

[ ALU LIGHTWEIGHT LOCATING COLLAR ORANGE (2) ]

[ O-RING 10X1MM BOTTOM CUP (4) ]

[ SUSPENSION ARM - 1/8TH LOWER REAR (2) ]

[ PIN 2.5x13  (10) ]

[ GRAPHITE RECEIVER BRACKET SET ]

[ SHOCK PISTON 16MM (8) ]

[ REAR HUB - L/R 1/8TH ]

[ PIN 3x17 (10) ]

[ GRAPHITE PERSONAL TRANSPONDER BRACKET ]

[ GT SHOCK SHAFTS ]

[ B HEAD SCREW (BM3*18MM) 16 PCS ]

[ PIN 2.5x16 (10) ]

[ COMPOSITE ROLL-OVER BAR WITH EYELET ]

[ COMPOSITE ANTENNA MOUNT ]

[ 6MM BALL STELL (NO COLLAR) ] 

[ ADDITIONAL XRAY ULTIMATE RACING SPRINGS (20) ]

[ REAR WING ]

[ XRAY SPRING-SET D=1.8 (33 LB) PURPLE - MEDIUM HARD ]

[ MOTOR MOUNT-UPPER/LOWER ]

[ XRAY SPRING-SET D=1.9 (38 LB) RED - HARD ]

[ MOTOR GEAR-15T/SET SCREW (M4X4MM) ]

[ SET C=4.0-5.6 -  REAR (2) ]

[ BEARING SET FOR IGT8 CLUTCH BELL - PINION MOD 1 ]

[ SERVO MOUNT ]

[ SET C=4.0-5.6 -  FRONT (2) ]

Mola de Amortecedor Progressiva Dianteira Original
Medida: 20mm / 1.5mm
Quant. 02

Aplicação:

XRAY NT1R
XRAY NT1 2009 Specs
XRAY NT1 2010 Specs
XRAY NT1 2011 Specs
XRAY NT1 2012 Specs
XRAY NT1 2013 Specs
XRAY NT1 2014 Specs
XRAY NT1 2015 Specs
XRAY NT1 2016 Specs
XRAY NT1 2017 Specs
XRAY NT1 2018 Specs
XRAY NT1 2019 Specs
XRAY NT1 2020 Specs
XRAY NT1 2021 Specs
XRAY NT1 2022 Specs
XRAY NT1 2023 Specs

[ SERVO ARM (2 PCS) ]

[ XRAY PROGRESSIVE SPRING SET C3.7-4.7 REAR  ]

[ BALL BEARING 8X16MM 2PCS ]

[ XRAY SPRING-SET D=1.7 (28.5 LB) DARK-BLUE  ]

[ BALL BEARING 13X20MM 4PCS ]

[ XRAY SPRING-SET D=1.7 (30.5 LB) VIOLET ]

[ BEARING SET FOR 2-SPEED CARRIER FOR IGT00200 ]

[ STEERING TIE ROD (2 PCS) 1/10 ]

[ XRAY SPRING-SET D=1.8 (38.5 LB) RED HARD ]

[ CHASSI MAXIMUS EP ]

[ XRAY SPRING-SET D=1.7 (28 LB) VIOLET MEDIUM ]

[ BALL-BEARING 5x8x2.5MM (2) ]

[ EP SIDE GUARD-L/R ]

[ CLUTCH SHOE - HIGH DYNAMIC - RED ]

[ BALL-BEARING 5x10x4MM (2) ]

[ BATTERY MOUNT A/B ]

[ CLUTCH SPRING MEDIUM ]

[ UPPER DECK MOUNT-F/R ]

[ MULT-FLEX 1 PIECE ALU ENGINE MOUNT ]

[ METAL SHIELDED BEARING SET FOR IGT800F10 ]

[ CENTER FRONT DRIVE SHAFT C ]

[ ALU 1 PIECE ALU ENGINE MOUNT MONOBLOCK ]

[ BEARINGS 6X10X3 (4 PCS) ]

[ EXHAUST MOUNTING WIRE EXTRA LONG ]

[ UPPER DECK C - 8382 ]

[ UPPER DECK D ]

[ SET SCREW, 4X10MM ]

[ UPPER DECK-E ]

[ ROUND BOTTOM DROOP DOWNSTOP SCREW ]

[ WIRE MOUNT-B ]

[ BALL-BEARING 12x18x4MM (2) ]

[ IGT8 PINION REMOVER TOOL FOR GT ]

[ PVC CAR BODY SHELL MAXIMUS EP ]

[ BAG IGT8 ]

[ BODY POST & CENTER BRACE ]

[ CENTRAL DIFF GEAR BOX COMPLETE ]

[ FUEL FILTER SMALL FOR B8 ]

[ CENTRAL DIFF SET ]

[ AIR FILTER SUPPORTER FOR NITRO BUGGY ]

[ MUFFLER STAY LONG ]

[ SPUR GEAR - 45T - OPTIMUS / MAXIMUS GP ]

[ LONGER ROD END PLASTIC FOR UPPER LINKS  ]

[ SILICONE O-RING 24X0.7 ]

[ RECEIVER & BATTERY BOX ]

[ SERVO SAVER SUS.ARM-UPPER ]

[ XRAY 3X2MM SILICONE O-RING ]

[ HEX ADAPTER/ M12 17MM NUT ]

[ SILICONE ORING 5X2 ]

[ BUMPER / UPPER SUS.ARM MOUNT-FRONT 8283/4 ]

[ PIN 2x8 (10) ]

[ BODY POST HOLDER/ BODY POST ]

Pneus c/ Roda Monster DHK Máximus

[ B HEAD SCREW BM3x24MM  (16) ]

[ ASEMBLY OF STEERING TIE ROD ]

[ HWX ADAPTER / M12 17MM NUT 8384 ]

[ CHASSIS - OPTIMUS/ MAXIMUS GP ]

[ SIDE GUARD - OPTIMUS/ MAXIMUS GP L&R ]

[ BATTERY CASE - OPTIMUS/MAXIMUS GP U/L ]

[ BATTERY HOLDER 4-CELL ]

[ BODY POST - 9831/2 F/R W/FUEL TUBING HOLDER ]